JC-LGL / LIGHTING JOURNAL

How to Calculate How Many LED Linear High Bay Lights You Need

Published By NioJaydonReading time 7 minBack to articles
How to Calculate How Many LED Linear High Bay Lights You Need?
At a glance

Learn how to estimate a preliminary LED linear high bay fixture count using area, target illuminance, fixture output, CU and LLF. Follow a manufacturing example that calculates 16 fixtures, then review the illustrative layout and the photometric checks needed before using the estimate for purchasing or installation.

How many LED linear high bay lights should you plan for in your space? The estimate depends on the area, target illuminance, exact fixture output, and project factors used in the calculation. This article shows how to use those inputs to estimate a preliminary fixture count, then check whether it fits the actual aisle and work-area layout.

How to Estimate a Preliminary Fixture Count

Use this method to estimate a preliminary fixture count for warehouses, manufacturing areas, workshops, and other commercial or industrial spaces. For each task zone, use its area, target illuminance, and the selected fixture’s listed lumen output; use mounting height to compare configurations, then check the result against the proposed layout.

Linear high bay lighting in warehouse aisles, storage areas and manufacturing workspaces.
Linear high bay lighting applications in warehouse and manufacturing environments.

Confirm the Inputs

Measure each task zone separately and multiply its length by its width to find the area. Identify the work surface where illuminance matters—for example, the floor for general storage or a workbench for assembly.

Use the ranges below as general planning references when selecting a target illuminance for a preliminary estimate. Lighting needs vary by task and facility, so treat the ranges as starting points rather than universal requirements.

Application Typical planning range
Basic warehouse storage 20–30 fc
General warehouse work 30–50 fc
Manufacturing areas 50–75 fc
Detailed assembly or inspection 75+ fc

Use mounting height to compare suitable fixture configurations. JC-LGL lists the following mounting-height and coverage guidance for its linear high bay options:

Mounting height (ft) Power (W) Output (lm) Coverage diameter (ft)
14–18 130 19,500 35–45
16–20 210 31,500 45–55
20–24 300 45,000 50–65
Over 24 400 60,000 ——

Use the height guidance to shortlist a suitable configuration, then use that configuration’s listed lumen output in the estimate. Compare available models in the JC-LGL LED linear high bay collection, or see the JC-LGL LED linear high bay product page for listed configurations and specifications. Height and coverage guidance alone do not confirm the light level for a specific task or layout.

For a quick preliminary estimate, use the JC-LGL LED Lighting Calculator below. Enter the room length, width, and height, then select a fixture type and usage category. The calculator displays an estimated fixture count, layout, and spacing.

Calculate and Round the Count

For a manual estimate, keep the units consistent: use foot-candles with square feet, or lux with square meters.

Preliminary fixture count = (target illuminance × area) ÷ (fixture lumens × CU × LLF)

CU, or coefficient of utilization, estimates how much of the selected fixture’s light reaches the work surface in a specific room. Ask the fixture manufacturer or lighting designer to determine a project-appropriate CU using the exact fixture’s photometric data, room dimensions, mounting height above the work surface, and room-surface reflectances.

LLF, or light loss factor, accounts for reductions in maintained output. Ask the manufacturer or lighting designer to establish a project-appropriate LLF using the fixture’s lumen-maintenance information and the expected dirt conditions and cleaning schedule.

  1. Measure the area of each task zone.
  2. Select a target illuminance for the task surface.
  3. Use mounting height to shortlist a fixture configuration, then record its listed lumen output.
  4. Obtain project-appropriate CU and LLF values before calculating.
  5. Substitute the inputs, calculate the result, and round a fractional count up to the next whole fixture.

Worked Example: A General Manufacturing Work Area

Consider a general manufacturing work area measuring 100 ft × 80 ft. Use the following illustrative inputs to estimate the fixture count:

Worked-example inputs
Input Example value
Room dimensions / area 100 × 80 ft / 8,000 sq ft
Target illuminance 50 fc
Mounting height 22 ft
Fixture configuration 300 W / 45,000 lm
CU / LLF 0.70 / 0.80

The 50 fc target is at the low end of the article’s 50–75 fc manufacturing planning range. The JC-LGL product page lists the 300 W / 45,000 lm configuration for a 20–24 ft installation-height range.

The room dimensions, target and factors are example inputs. CU = 0.70 and LLF = 0.80 are illustrative values, not JC-LGL project recommendations or fixed defaults. Use project-specific measurements and lighting data for an actual estimate.

Substitute the inputs into the fixture-count formula:

Preliminary fixture count = (target illuminance × area) ÷ (fixture lumens × CU × LLF)
= (50 fc × 8,000 sq ft) ÷ (45,000 lm × 0.70 × 0.80)
= 400,000 ÷ 25,200
= 15.87

Planning result: round 15.87 up to 16 fixtures.
This is an average-light estimate for the stated inputs, not a verified point-by-point result.

Does the Count Fit the Layout?

For a layout illustration, assume four similar production lines run along the room’s 100 ft length and are evenly spread across its 80 ft width. Assume mounting points above each line can maintain the 22 ft height used in the calculation.

One row of linear high bays over each line gives four rows. Four fixtures per row use the preliminary total of 16. This production-line arrangement is illustrative; the fixture-count formula does not determine the number of rows.

Center each row within one of four equal 20 ft-wide strips. Along each row, center a fixture in each of four 25 ft-long sections. This gives 20 ft between rows and 25 ft between fixtures along a row.

Conceptual 16-fixture layout in a 100 by 80 foot room

Conceptual layout for the worked example: 100 × 80 ft, with 25 ft between fixtures along each row and 20 ft between rows. Fixtures are centered in each cell, giving wall offsets of 12.5 ft and 10 ft. These dimensions illustrate the geometry; they are not verified spacing limits or a photometric result.

These distances come from dividing the example space into equal sections; they are not recommended spacing limits for the selected fixture.

Check the sketch against the actual work areas and equipment. A machine may block a mounting point, or a workstation near an edge may fall outside a row.

If the production lines or mounting limits differ, shift or redistribute the 16 fixtures and review the revised layout before treating the count as a project quantity.

When Is Further Validation Needed?

Are the 20 ft row spacing and 25 ft along-row spacing suitable? Geometry alone cannot answer that question. Before treating 16 fixtures as a purchasing or installation count, test the candidate arrangement using photometric data for the exact 300 W configuration.

The listed 45,000 lm output supports the preliminary count, but it does not show the light reaching workstations between rows, near edges or behind equipment. Validate the arrangement in these steps:

  1. Build a scaled floor plan. Include the four rows, their 20 ft and 25 ft center-to-center distances, production lines, workstations and obstructions.
  2. Set the calculation surfaces and run the model. Confirm the fixture height above each work surface and include the actual work-plane heights. Run a photometric calculation using data for the selected 300 W configuration to predict illuminance across those work surfaces.
  3. Compare the predicted average illuminance. Compare the predicted average illuminance across the manufacturing work surfaces with the example’s 50 fc planning target. Separately check low-light areas between rows, near edges and around equipment.
  4. Check uniformity and revise. If the project specifies a uniformity criterion, check it as well. Adjust fixture positions, spacing or count where needed, then test again.
Industrial lighting layout with a photometric illuminance heatmap
Illustrative lighting distribution only; this image does not verify the worked example’s 16-fixture layout.

Conclusion

In the worked manufacturing example, the calculation gives a preliminary count of 16 LED linear high bay fixtures. Your count will depend on your task area, target illuminance, selected fixture’s listed light output, and project-specific calculation factors. Use the same method with your project’s inputs; the example’s 16 fixtures are not a universal recommendation.

You can use the JC-LGL 3D Lighting Studio to explore fixture positions and compare estimated ground illuminance.

Opens in a new tab.

Share this article

Comments 0

Be the first to leave a comment.

Leave a comment

Your email address will not be published. Required fields are marked *.

Please note, comments must be approved before they are published.